Welcome Guest!!

Welcome to SCCX, for full access to the forums, please register and join our community, it's free.

Author Topic: KickinTires' 2011 Avalanche PRO-4X Frontier  (Read 17956 times)

KickinTires

  • Jr. Member
  • **
  • Posts: 70
  • 4wd Pts: 9
KickinTires' 2011 Avalanche PRO-4X Frontier
« on: June 19, 2013, 10:10:26 PM »
Joined SCCX: May 01, 2011
Username:  KickinTires
Real Name: Mark
Year:  2011
Make:  Nissan
Model: Frontier (Crew Cab)
Trim:  4x4 PRO-4X 6-spd
Color:  Avalanche White
Mods:
   Suspension:  
         PRG UCAs
         2.0 PRG Radflo Coilovers
         Bilstein 5125 0-3" Lift
         PRG Deaver AAL
    Wheels and Tires:
         BF Goodrich All-Terrain K/O (265/75/16)
    Armor:
         Shrockworks Sliders, Rear Diff Plate
         Shrockworks Skids;
            Engine, Transmission, Transfer Case, Gas Tank,
             and Radiator
   Communication:
               Midland 1001 LWX
               Firestik 18' Coax
                Firestik Firefly 3' w/ Firestik Quick Disconnect

   Extras:
         Leer 700 tonneau cover
         Nissan hood protector
         XPEL lens kit
         RotoPax 3-Gal w/ Utilitrac Mount
         Hi-Lift Jack /w Titus Products Hi-Lift Mount
         Bumper mounted Trailer Harness Receptacle
         Pathfinder Switch Plates
   Future Mods:
         BlueSea 12-Fuse Curcuit
         Direct wired; GPS, CB, and Inverter
         Anderson Powerpole  6ft Pigtail for Air Compressor
         ARB or CVT Awning mounted cross-wise underside of Tonneau w/ side curtains
         Roof Rack Rails on Tonneau w/ BajaRack of some sort???


        
Comments:  I wanted a very capable rig for running Greens and some Blues and basically get my Camera further off the pavement!

Photos:  Some of my Mods and Outings with SCCX and friends...

Stock off of Dealers Lot...


Leer 700 Tonneau Cover..


ShrockWorks Sliders Installed...


ShrockWorks Skids and Diff Plate installed...


New BFG All-Terrains...


PRG UCAs and 2.0 PRG Radflo Coilovers


Lifted just right...


Trailer Harness Bumper Mod...


CB Antenna Mount...


CB Out of Service...


First Run w/ SCCX - Buttes Pass Area


SCCX Run - Blair Valley


SCCX Run - Big Bear - CANVAS 2012




« Last Edit: June 20, 2013, 06:56:49 PM by KickinTires »
Mark

Club Frontier Member "KickinTires"

SD_Frontier

  • Full Member
  • ***
  • Location: San Diego, CA
  • Posts: 216
  • 4wd Pts: 14
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #1 on: June 20, 2013, 12:33:33 AM »
Clean!
2005 Super Black (and white) Crew Cab SE 4x4

Code Name: SHAMU

Build Thread

SoCalXTerry

  • Hero Member
  • *****
  • Location: Northern Orange County
  • Posts: 1273
  • 4wd Pts: 54
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #2 on: June 20, 2013, 05:39:48 AM »
Very nice.   TOO clean   ;)
Terry

Greasy side down - K6XTL

Motorpig77

  • Sr. Member
  • ****
  • Posts: 289
  • 4wd Pts: 31
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #3 on: June 20, 2013, 10:46:26 AM »
Nice truck!  Do you have any pics of the rotopax 3gal utilitrack mounts?

Toro

  • Hero Member
  • *****
  • Posts: 2066
  • 4wd Pts: 126
  • yep, Dos XX and Chipotle
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #4 on: June 20, 2013, 12:59:45 PM »
Yep, deff getting a Frontier.

KickinTires

  • Jr. Member
  • **
  • Posts: 70
  • 4wd Pts: 9
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #5 on: June 20, 2013, 06:51:14 PM »
Nice truck!  Do you have any pics of the rotopax 3gal utilitrack mounts?

I can take some for you if you'd like.  Not really impressed with the Utilitrak mount.  It is rather flimsy and that 3 Gal Pak with it's weight will be vibrating all over the place.  I'm going to a least make a brace to connect to the trak on the floor at that end of the bed...


Very nice.   TOO clean   ;)

I'm still running around town with the dirt from Mojave Road; does that count?
« Last Edit: June 20, 2013, 06:52:49 PM by KickinTires »
Mark

Club Frontier Member "KickinTires"

Ghost65

  • Old-Schooler
  • Hero Member
  • *****
  • Location: East of You
  • Posts: 862
  • 4wd Pts: -476
    • 2019 Ready Mix Taco
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #6 on: June 21, 2013, 06:18:04 AM »
Yep, deff getting a Frontier.

Seriously...no kidding.
KD6DCI

Once again, I must state for the record: We are not a club, we are enablers for your addiction.

KickinTires

  • Jr. Member
  • **
  • Posts: 70
  • 4wd Pts: 9
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #7 on: June 29, 2013, 05:53:50 PM »
Nice truck!  Do you have any pics of the rotopax 3gal utilitrack mounts?

Motorpig77;  Sorry, it took me awhile to get these posted...

Here are a couple of the Utilitrak mount as attached to the trak, the top is generally secure, but the plate with the weight has nothing to stop it from vibrating fore/aft.


I just want to attach a short 'L' brace from the floor trak to the bottom of the plate.


Now with the 3 Gal RotoPax mounted, it clears well on top and bottom




That's it, I'm sure it can be improved.   Maybe the entire mount can be a DIY project as well...
« Last Edit: June 30, 2013, 11:01:32 AM by KickinTires »
Mark

Club Frontier Member "KickinTires"

Motorpig77

  • Sr. Member
  • ****
  • Posts: 289
  • 4wd Pts: 31
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #8 on: June 30, 2013, 01:12:26 AM »
Thanks for the pics...I can see where it could use some reinforcing to make them more stable back there. I'll look into it and see what I can up with!

SD_Frontier

  • Full Member
  • ***
  • Location: San Diego, CA
  • Posts: 216
  • 4wd Pts: 14
Re: KickinTires' 2011 Avalanche PRO-4X Frontier
« Reply #9 on: June 30, 2013, 09:15:03 AM »
Ooh I like those. I might mount my hi lift vertically and get some rotopax and mounts. Lemme know how you reinforce the bottom.
2005 Super Black (and white) Crew Cab SE 4x4

Code Name: SHAMU

Build Thread

 


Powered by EzPortal