Topic: RikRong's BluX build...Sshhiinnyyy....

[lutsie]

What are the updated measurements?


Sent from my iPhone using Tapatalk

[RikRong]

What are the updated measurements?


Sent from my iPhone using Tapatalk

I think we measured it at about 39" right after the install, that's about 2" higher than it was before.  However, it has settled quite a bit, so I'm going to measure again when I get back home tomorrow.

Sent from my XT1575 using Tapatalk

[lutsie]

Awesome.


Sent from my iPhone using Tapatalk

[GreenAcres]

Looks fantastic!  Amazing to see you guys pull of such a significant mod so quickly and with such a good outcome! Well done.

[SyK0]

Looks great! Hope to see it in person in the next SCC or SCXF meet 

What were your fender to ground measurements before the swap??

[lutsie]

Looks great! Hope to see it in person in the next SCC or SCXF meet 

What were your fender to ground measurements before the swap??

He listed in post 82. Been following intently I'm thinking of going this route


Sent from my iPhone using Tapatalk

[RikRong]

Looks great! Hope to see it in person in the next SCC or SCXF meet 

What were your fender to ground measurements before the swap??

Yeah, check out that post, I can't remember exactly where I was at. I will post updated specs when I get home.

Sent from my XT1575 using Tapatalk

[RikRong]

Well, here's the good stuff...

First off, deduct .5" off the measurements I posted in post #82. I measured with the tape straight today. With it bent, the measurements were off about .5". Anyway, new height is 38.25" from fender to ground, front and rear. 23.5" from fender to hub, front and rear.


Sent from my XT1575 using Tapatalk

[Jayrat]

Rock "N" Roll Buddy 

[Toro]

Sexy as F!

Sent from my SAMSUNG-SM-G891A using Tapatalk

[Kjswa]

Looks killer!! You've got yourself a great rig! Only 4 hours? I helped a friend replace the ball joints and coil-overs on his '96 Tacoma took three of us 2 days. Haha

[RikRong]

Looks killer!! You've got yourself a great rig! Only 4 hours? I helped a friend replace the ball joints and coil-overs on his '96 Tacoma took three of us 2 days. Haha

Well, it was little over 4, to be fair.  haha  I was on one side, Toro was on the other. Woody and OccupantX plugged away on the skids and then the diff, while we were working on the suspension.  It was a pretty good team. 

[SyK0]

Looks awesome man! Saw the pics on IG first.

Did you have your front sway bar on before the swap??

[RikRong]

Looks awesome man! Saw the pics on IG first.

Did you have your front sway bar on before the swap??

Thank-you.  The truck is a little bit of an IG whore.   

I did have the sway bar installed prior.  At this point, I wish I had removed it a long time ago.

[SyK0]

Thank-you.  The truck is a little bit of an IG whore.   

I did have the sway bar installed prior.  At this point, I wish I had removed it a long time ago.

Haha, mine has taken over my page too.

Ahhh, dang.  I was hoping you had it off before to see how much of a difference it was with your aftermarket suspension vs. titan swap. I was thinking most guys say its a huge difference because most run sway bars and then with a titan swap they don't have one for the first time. No front sway really is a huge difference.