Author Topic: White Knuckle Sliders Group Buy! (GB is CLOSED) (Read 45825 times)

beedee · « **Reply #135 on:** June 16, 2016, 09:43:30 AM »

Quote from: Celt on June 16, 2016, 05:16:59 AM

You can always weld them up and never have to worry about it again.

I have thought about that too. Any idea of what that would cost?

valentin36 · « **Reply #136 on:** June 16, 2016, 10:14:22 AM »

Hahaha this be our attempt to save a penny

beedee · « **Reply #137 on:** June 16, 2016, 11:59:15 AM »

I shotgunned a quote out via Yelp to local muffler/weld shops. Most are coming back around $150 with a 2-3 hour job scope.

Ghost65 · « **Reply #138 on:** June 16, 2016, 12:32:52 PM »

Quote from: Celt on June 16, 2016, 05:16:59 AM

You can always weld them up and never have to worry about it again.

This.

I had my Shrockworks sliders welded onto my X by Jason at ORW in San Marcos. Cost $160, but they were s-o-l-i-d. A good consideration esp since we all use our sliders as Hi Lift points of contact when...jacking.

knightrider · « **Reply #139 on:** June 18, 2016, 12:46:36 AM »

i have also not drilled the extra holes and have had no issues landing on my sliders, i've checked the mounting bolts a few times in the 3-4 years and they have not loosened up at all.

Celt · « **Reply #140 on:** June 18, 2016, 05:15:45 AM »

Quote from: beedee on June 16, 2016, 09:43:30 AM

I have thought about that too. Any idea of what that would cost?

I couldn't quote you a cost but I know someone who can do it and make sure it's done right.

valentin36 · « **Reply #141 on:** June 18, 2016, 07:08:35 AM »

Quote from: knightrider on June 18, 2016, 12:46:36 AM

i have also not drilled the extra holes and have had no issues landing on my sliders, i've checked the mounting bolts a few times in the 3-4 years and they have not loosened up at all.

Did you use anything on them, like loctite or similar to it or just your hands and prayer that they don't fall off??

Celt · « **Reply #142 on:** June 18, 2016, 07:44:01 AM »

Quote from: valentin36 on June 18, 2016, 07:08:35 AM

Did you use anything on them, like loctite or similar to it or just your hands and prayer that they don't fall off??

If you do not plan to weld them, lock washers and some lock-tite is a very good idea.

Sage Bromax · « **Reply #143 on:** June 18, 2016, 08:49:34 AM »

Quote from: Celt on June 18, 2016, 07:44:01 AM

If you do not plan to weld them, lock washers and some lock-tite is a very good idea.

I used lock washers, nylocks or locktite on all the bolts.

beedee · « **Reply #144 on:** June 18, 2016, 01:26:50 PM »

Quote from: Celt on June 18, 2016, 05:15:45 AM

I couldn't quote you a cost but I know someone who can do it and make sure it's done right.

Where at?

Celt · « **Reply #145 on:** June 18, 2016, 01:32:19 PM »

Quote from: beedee on June 18, 2016, 01:26:50 PM

Where at?

Give Jeremy a call at Weldtec Designs 619-596-9831. He's done several projects for me in the past and everything has been top notch.

Here is his website: http://www.weldtecdesigns.com/

beedee · « **Reply #146 on:** June 18, 2016, 01:35:06 PM »

Quote from: knightrider on June 18, 2016, 12:46:36 AM

i have also not drilled the extra holes and have had no issues landing on my sliders, i've checked the mounting bolts a few times in the 3-4 years and they have not loosened up at all.

How many bolts does that end up being in each arm of the sliders?

beedee · « **Reply #147 on:** June 22, 2016, 09:28:25 PM »

Installed them tonight with the help of my buddy.